KJCOEMR
Mechanical Engineering-Research & Publications

Mechanical Engineering


Research & Publications

BCUD Grant:

Ajit M Kate, BCUD research grant, 2009-2011 of University of Pune on “Investigation of Thermal Performance and Heat Transfer Characteristics of Wickless Heat Pipes,” amount sanctioned Rs. 1.25 lakhs.

Publications

  • International & National Journal Publications
  • Ajit M Kate, “Experimental Investigation of Elliptical Cross Section geometry Wickless Heat Pipe Charged with Distilled Water and Ethanol,” International Review of Mechanical Engineering (IREME), Vol.5, No.2,pp. 369-375, February 2011 (ISSN 1970-8734)
  • Ajit M Kate, ”Effect of Pipe Cross Section Geometries and Inclination Angle on Heat Transfer Characteristics of Wickless Heat Pipe,” International Journal of Engineering Research Technology, Vol.3, No.3,pp. 699-710, June 2010(ISSN 0974-3154)
  • Ajit M Kate, Adhiyaman College of Engineering (ISTE Chapter-2006), Hosur (Tamilnadu), September 06-08, 2006, “Parabolic Solar Concentrator using Digital Tracking,” pp. 105-110
  • Ajit M Kate,Adhiyaman College of Engineering (ISTE Chapter-2006), Hosur (Tamilnadu), September 06-08, 2006, “Implementation of Six Sigma for World class quality,” pp. 125-131
  • Ajit M Kate, Solar Energy Society of India (SESI),MITCON,IIT, Powai, January 20-22, 2005, “Solar Water Pasteurizer,” pp.82-86.
  • Ajit M Kate,Shri Siddhartha Institute of Technology, Tumkur (Karnataka), September 25-27, 2004, “Design and Testing of Solar Water Pasteurizer,” pp.115-121.
  • RohanGhorpade, Rahul Parikh, ParagGholawde, AmolPangare, Mr. MukeshChaudhari, “To Check Tir Of Gears Using Hydro Pneumatic Intensifier After Heat Treatment”, International Journal of Enhanced Research in Science Technology & Engineering, ISSN: 2319-7463, Vol. 3 Issue 5, May-2014, pp: 95-100.
  • AtulYadav, SidharthSawant, ChetanPujari, Siddesh Mehta, Mr. MukeshChaudhari, “ Pick and Place Robotic system for assembly of Thermostat Radiator valve” , International Journal of Innovative Research & Development, Vol 3 Issue 5, May, 2014 ISSN 2278 – 0211.
  • Rishikesh H. Tike, Prof. Mukesh C. Chaudhari, “The Airbag System For 2-Wheeler Vehicle System”, International Journal Of Research In Aeronautical And Mechanical Engineering, ISSN : 2321-3051, Vol.2 Issue.2, February 2014.
  • MukeshChaudhari and B.R. Kharde, “Optimization of bonnet thickness for adult pedestrian safety- A FEA approach, The International Journal of Pure and Applied Research in Engineering and Technology, April 2013, Volume 1(8) pp 23-34.
  • MukeshChaudhari and B.R. Kharde, “ Procedure to obtain the bonnet thickness for adult pedestrian head safety”, IJERT, Vol 2, Issue 7, July-2013.
  • MukeshChaudhari, “Comparative Evaluation for Pedestrian Safety Systems”, IJTARME, Volume-2, Issue-4, 2013.
  • Nikhil M. Shinde, “Optimization of Single Roller Burnishing Operation for Surface Roughness and surface hardness of Aluminium Alloy Using Artificial Neural Network.”International Journal of Applied Engineering Research, ISSN 0973-4562 Vol.10 No.71 (2015)

National and International Conference

  • C M Gajare, “Recent Changes in Mechanical Engg. Design” in International Journal Bearing ISSN .
  • Rameez A. Hudli, Essential Practical Parameters for Setting up a New Assembly Line for Pump sets Coupled with Diesel Engines, International Journal of Advanced Manufacturing Systems (IJAMS), SardarVallabhbhai National Institute of Technology, Surat, Gujarat State, India, July to Dec 2011 (ISSN: 2229-5860).
  • Rameez A. Hudli, Areas of Lean Manufacturing for Productivity Improvement in a Manufacturing Unit, International Conference on Manufacturing and Industrial Engineering 2010, World Academy of Science, Engineering and Technology, Amsterdam, The Netherlands, Issue - 69:2010.
  • Rameez A. Hudli, Essential Practical Parameters for Setting up a New Assembly Line for Pump sets Coupled with Diesel Engines, 4th International Conference on Advances in Mechanical Engineering (ICAME) 2010, SardarVallabhbhai National Institute of Technology, Surat, Gujarat State, India.
  • Rameez A. Hudli, Semi-Automatic Metal Spinning Machine, International Journal of Engineering Trends and Technology (IJETT), April 2013, ISSN: 2231-5381.
  • S.S.Jadhav, RameezA. Hudli, “Assembly Tolerance Analysis by using crystal ball- A case study”, published in International Journal of Current Engineering and Technology (IJCET) ISSN:2277 – 4106.
  • S.S.Jadhav, Rameez A. Hudli, “Surface Grinding Process - Modeling & Simulation for Comparing the< Performance of different Coolants”, published in (IJCET) ISSN: 2277 – 4106.
  • S. S. Jadhav, S.G.Mandave, “A Review on Metal Matrix Composites and its Machining”, published at Proceedings of ISET2015, International Conference on Design, Manufacturing and Mechatronics ICDMM2015.
  • Rameez A. Hudli, High Altitude Airborne Wind Energy Turbine: Review and Comparison of Airborne Turbines, International conference on Design, Manufacturing and Mechatronics, KJEI’s, K.J College of Engineering and Management Research Pune, India February 13-14 2015.
  • Subhash L. Gadhave, Mechatronics [T.E Mech. SPPU] “ Technical Publication”  First Edition Jan 2013, Second Revised Edition Jan 2015 ISBN: 9789350999042.
  • Subhash L. Gadhave, Energy Audit and Management[B.E Mech. SPPU]  “ Techmax Publication” First Edition July 2015, ISBN: 9789352241064 .
  • MukeshChaudhari, YogendraGirase, “Mechatronics-future scope important” national conference, Avishkar arrange by SNDCOE & Research Center Yeola, Nasik, MH, India, 423401, March 26-27, 2012.
  • Subhash L. Gadhave, Robotics [B.E Mech. SPPU]   “ Technical Publication” First Edition Feb 2016, ISBN: 9789333209724.
  • Subhash L. Gadhave, Mechatronics  DECODE [T.E Mech. SPPU] “ Technical Publication”  First Edition Jan 2015 ISBN: 9789333210324.
  • Subhash L. Gadhave, Industrial Engineering DECODE [B.E Mech. SPPU]  “ Technical Publication” First Edition Feb 2016, ISBN: 9789333210386.
  • Subhash L. Gadhave, Project Management and Engg. Economics DECODE [T.E Civil. SPPU] “ Technical Publication”  First Edition March 2016.
  • Subhash L. Gadhave, Measurement and Metrology DECODE [S.E Mech. UPPU] “ Technical Publication”  First Edition March 2016.
  • Subhash L. Gadhave, Mechatronics DECODE [B.E Mech. UPPU] “ Technical Publication”  First Edition March 2016
  • Ajay G. Waychal, Pravin Ingle,Ajit M. Kate, “Performance Analysis and Emission Testing of Speed and Variable Load of Diesel Engine Fueled with Diesel-Ethanol-Biodiesel Blends”, International Conference on Design, Manufacturing and Mechatronics, February-2015.
  • Ajay G. Waychal, “Reverse Logistics Networks Structure and Design”, International Conference on Design, Manufacturing and Mechatronics, February-2015.
  • Gayatri S. Patil, “Transverse Strength analysis of 304SS Weld Joint”, International conference on advances in materials and product design held at NIT, Surat on 10th& 11th Jan. 2015.
  • Gayatri S. Patil, “Natural Frequency Analysis of Composite Sandwich”, International conference on Design, manufacturing and Mechatronics held at KJCOEMR, Pune on 11th to 13th Feb. 2015.
  • Gayatri S. Patil, “Strength Analysis of Austenitic steel weld joint”, International conference on Design, manufacturing and Mechatronics held at KJCOEMR, Pune on 11th to 13th Feb. 2015.